Available in sizes from 1/4" (M6) to 1-1/2" (38 MM) Other sizes available by special order.
Available in 1010 Carbon Steel
Carbon Steel washers are case hardened and coated with RoHS-compliant Delta Protekt®
Provided in pre-assembled, glued pairs
Easy to install with standard tools
No re-tightening needed once installed
Vibration proof according to MIL-STD-1312-7
Proven Results Disc-Lock® Locking Washer Junker Test
Disc-Lock® Wedge Locking Washers have been tested on a Junker Vibration Machine. The Junker test considered the most severe vibration test for bolted joints according to DIN 65151, is used to determine the point at which a bolted joint loses its preload when subjected to shear loading due to transverse vibration.
When tested against a standard washer using the Junker test, Disc-Lock® Wedge Locking Washers remained secure under severe vibration conditions, while the standard washer loosened significantly.
Proven Applications Disc-Lock® Wedge Locking Washers outperform conventional, split-ring, and other style washers in a wide variety of high stress, corrosive, and vibration-sensitive applications including:
Agriculture Equipment
Automotive
Construction Equipment
Heavy Rail
Logging Equipment
Marine
Military
Mining
Oil Drilling Equipment
Solar
Wind
Waste Management
Installation
To install the Disc-Lock® Washer, place the preassembled pair of washers between the nut and the joint material.
As the nut is tightened, one half of the Disc-Lock® Washer is seated to the joint material and the other to the nut.
Disc-Lock® Washers should only be used against flat, relatively smooth metal surfaces.
If the joint material is not metal, the Disc-Lock® washer may be used by securing the metal plate to the joint material in such a manner that the metal plate will not rotate.
A torque wrench is not required to install Disc-Lock® Washers.
An air-gun can be used when installing and removing Disc-Lock® Washers.
If installed correctly, the Disc-Lock® Washer will ensure that the fastener remains secure, and will not require any re-tightening.
Torque Guidelines When installing Disc-Lock® Washers in a common application, expect an increase in required torque over recommended installation torque to achieve proper clamp load and maximum joint safety. Due to varying installation conditions and customer-specific applications, additional information and torque recommendations are available by contacting Engineering support at Disc-Lock®.
Note Weight and thickness of pairs will vary slightly with gauge of metal.
Coated in Delta Protekt® KL100 and VH302 GZ.
Disc-Lock® Wedge Locking Washers are also available through our Made in the U.S.A. product line
Available in sizes from 1/4" (M6) to 1-1/2" (38MM) Other sizes available by special order.
Available in 316L Stainless Steel
Carbon Steel washers are case hardened and coated with RoHS-compliant Delta Protekt®
Provided in pre-assembled, glued pairs
Easy to install with standard tools
No re-tightening needed once installed
Vibration proof according to MIL-STD-1312-7
Proven Results Disc-Lock® Locking Washer Junker Test
Disc-Lock® Wedge Locking Washers have been tested on a Junker Vibration Machine. The Junker test, considered the most severe vibration test for bolted joints according to DIN 65151, is used to determine the point at which a bolted joint loses its preload when subjected to shear loading due to transverse vibration.
When tested against a standard washer using the Junker test, Disc-Lock® Wedge Locking Washers remained secure under severe vibration conditions, while the standard washer loosened significantly.
Proven Applications Disc-Lock® Wedge Locking Washers outperform conventional, split-ring, and other style washers in a wide variety of high stress, corrosive, and vibration-sensitive applications including:
Agriculture Equipment
Automotive
Construction Equipment
Heavy Rail
Logging Equipment
Marine
Military
Mining
Oil Drilling Equipment
Solar
Wind
Waste Management
Installation
To install the Disc-Lock® Washer, place the preassembled pair of washers between the nut and the joint material.
As the nut is tightened, one half of the Disc-Lock® Washer is seated to the joint material and the other to the nut.
Disc-Lock® Washers should only be used against flat, relatively smooth metal surfaces.
If the joint material is not metal, the Disc-Lock® washer may be used by securing the metal plate to the joint material in such a manner that the metal plate will not rotate.
A torque wrench is not required to install Disc-Lock® Washers.
An air-gun can be used when installing and removing Disc-Lock® Washers.
If installed correctly, the Disc-Lock® Washer will ensure that the fastener remains secure, and will not require any re-tightening.
Torque Guidelines When installing Disc-Lock® Washers in a common application, expect an increase in required torque over recommended installation torque to achieve proper clamp load and maximum joint safety. Due to varying installation conditions and customer-specific applications, additional information and torque recommendations are available by contacting Engineering support at Disc-Lock®.
Note Disc-Lock® Wedge Locking Washers are also available through our Made in the U.S.A. product line.
